大主宰txt全集下载,怎么写网络小说

蘇州工業園區翔宇電子有限公司

化學用品一站式服務????

化工生產銷售?????

熱點詞推薦：

產品展示?/Product

ABOUT MOUMOU?

網站首頁 >> 厭氧膠

產品展示

DEDT3215

厭氧膠

市場價:0.00

價格:0.00

<h1>PRODUCT DESCRIPTION</h1>DEDT 3215 is a single component anaerobic threadlocking material, which is develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces. <h5>TYPICAL APPLICATIONS</h5>* Prevents loosening and leakage of threaded fasteners.* Cylinder liner studs.* Air compressor fasteners.* Refrigeration safety valves.                                                                                                                                                                                            <h5>POLYMER PROPERTIES</h5>TypicalValue        RangeChemical Type                                                                 Dimethacrylate esterAppearance                                                                   Blue liquidSpecific Gravity                                                               1.1Viscosity (at 25°C) (mPa.s)                                               7000       5000 to 9000Flash Point (TCC) °C                                              >93 <h5>CURE SPEED VS. SUBSTRATE</h5>The rate of cure will depend on substrates involved.Substrate                                                                   Fixture time/Full cureSteel                                            30min/24hrsBrass                                            40min/24hrsZn Dichromate                                    50min/24hrs<h6>Stainless Steel                                     60min/24hrs</h6><h6> </h6><h6>CURE SPEED VS. BOND GAP</h6>The rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap will decrease the rate of cure.<h1> </h1><h1>CURE SPEED VS. ACTIVATOR</h1>Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed, But may also impair overall adhesive performance and therefore testing is recommended to confirm effect. <h6>CURE SPEED VS. TEMPERATURE</h6>The rate of cure will depend on the ambient temperature. High temperature tend to increase the speed.TYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts (N.m).  TypicalValue       RangeBreakaway Torque                                                             31         25~35Prevailing Torque                                                              35         28~40 <h1>GENERAL INFORMATION</h1>This product is not recommended for use in pure oxygen or rich systems and should not be selected as sealant for chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check for compatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect the cure and performance of the adhesive.This product may not be compatible with plastics, (particularly thermoplastic materials where stress cracking of plastic could result). Users are advised to confirm compatibility of the product with such substrates. <h1>DISASSEMBLY AND CLEANUP PRODUCT</h1>To aid in disassembly, DEDT anaerobic compounds can be weakened by heating to at least 260℃. Once disassembled ,cured adhesive can removed with DEDT Gasket Remover1790 by following instructions. A solvent wipe with an organic or petroleum solvent will remove uncured adhesive outside the joint. PRODUCT STORAGE Product should be stored in a cool, dry location in unopened containers at a temperature between c between 46℉ (8℃) to 82℉ (28℃) unless otherwise stated. To prevent contamination of unused product, do not return any material to its original container. DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliable at the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have no control. It is the responsibility of the customer to determine the products suitability for use. DEDT New materials Limited and its associated companies accept no liability arising out of the use of this information or the products described herein.
DEDT3242

厭氧膠

市場價:0.00

價格:0.00

PRODUCT DESCRIPTIONDEDT 3242 is a single component anaerobic threadlocking material, which is thixotropic and developsmedium strength . The product cures when confined in the absence of air between close fitting metalsurfaces.TYPICAL APPLICATIONS*Prevents loosening and leakage of threaded fasteners.*Pump and motor mounting bolts.*Engine rocker nut*Situations were disassembly with hand tools is required.POLYMER PROPERTIESTypicalValue RangeChemical Type Dimethacrylate esterAppearance Blue liquidSpecific Gravity 1.05Viscosity(at 25°C)(mPa.s) 2000 1200 to 2800Flash Point(TCC) °C >93CURE SPEED VS. SUBSTRATEThe rate of cure will depend on substrates involved.Substrate Fixture time/Full cureSteel 15min/24hrsBrass 20min/24hrsZn Dichromate 30min/24hrsStainless Steel 40min/24hrsCURE SPEED VS. BOND GAPThe rate of cure will depend on the bondine gap. The bondlines result in high cure speeds, increasing thebond gap will decrease the rate of cure.CURE SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps, applying activator to the surface will improvecure speed, But may also impair overall adhesive performance and therefore testing is recommended toconfirm effect.CURE SPEED VS. TEMPERATUREThe rate of cure will depend on the ambient temperature. High temperature tend to increase the speedTYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts(N/mm2)TypicalValue RangeBreakaway Torque 19 14~25Prevailing Torque 8 4~11GENERAL INFORMATIONThis product is not recommended for use in pure oxygen rich systems and should not be selected as sealantfor chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check forcompatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect thecure and performance of the adhesive.This product may not be compatible with plastics,(particularly thermoplastic materials where stresscracking of plastic could result). Users are advised to confirm compatibility of the product with suchsubstrates.DIRECTIONS FOR USEFor best results, surfaces should be clean and free of grease. 3243 should be applied to the bolt in adequatequantity to fill all engaged threads. 3243 performs best in thin bond gaps, (0.05mm). Very large thread sizesmay create large gaps which will affect cure speed and strength. This product is designed to give controlledfriction, (torque/tension ratio), during assembly. In cnitical tightening applications this ratio should beconfirmed.PRODUCT STORAGEProduct should be stored in a cool, dry location in unopened containers at a temperature between containersat a temperature between 46℉ (8℃)and 82℉ (28℃)unless otherwise stated. To prevent contamination ofunused product, do not return any material to its original container.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed tobe reliable at the time of issue. We cannot assume responsibility for results obtained by others over whosemethods we have no control. It is the responsibility of the customer to determine the products suitability foruse. DEDT Limited and its associated companies accept no liability arising out of the use of thisinformation or the products described herein.
DEDT3217

厭氧膠

市場價:0.00

價格:0.00

<h1>PRODUCT DESCRIPTION</h1>DEDT 3217 is a single component anaerobic threadlocking material, which is develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces. <h5>TYPICAL APPLICATIONS</h5>* Prevents loosening and leakage of threaded fasteners.* Cylinder liner studs.* Air compressor fasteners.* Refrigeration safety valves.                                                                                                                                                                                            <h5>POLYMER PROPERTIES</h5>TypicalValue        RangeChemical Type                                                                 Dimethacrylate esterAppearance                                                                   Red liquidSpecific Gravity                                                               1.1Viscosity (at 25°C) (mPa.s)                                               7000       5000 to 9000Flash Point (TCC) °C                                              >93 <h5>CURE SPEED VS. SUBSTRATE</h5>The rate of cure will depend on substrates involved.Substrate                                                                   Fixture time/Full cureSteel                                            30min/24hrsBrass                                            40min/24hrsZn Dichromate                                    50min/24hrs<h6>Stainless Steel                                     60min/24hrs</h6><h6> </h6><h6>CURE SPEED VS. BOND GAP</h6>The rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap will decrease the rate of cure.<h1> </h1><h1>CURE SPEED VS. ACTIVATOR</h1>Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed, But may also impair overall adhesive performance and therefore testing is recommended to confirm effect. <h6>CURE SPEED VS. TEMPERATURE</h6>The rate of cure will depend on the ambient temperature. High temperature tend to increase the speed.TYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts (N.m).  TypicalValue       RangeBreakaway Torque                                                             31         25~35Prevailing Torque                                                              35         28~40 <h1>GENERAL INFORMATION</h1>This product is not recommended for use in pure oxygen or rich systems and should not be selected as sealant for chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check for compatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect the cure and performance of the adhesive.This product may not be compatible with plastics, (particularly thermoplastic materials where stress cracking of plastic could result). Users are advised to confirm compatibility of the product with such substrates. <h1>DISASSEMBLY AND CLEANUP PRODUCT</h1>To aid in disassembly, DEDT anaerobic compounds can be weakened by heating to at least 260℃. Once disassembled ,cured adhesive can removed with DEDT Gasket Remover1790 by following instructions. A solvent wipe with an organic or petroleum solvent will remove uncured adhesive outside the joint. PRODUCT STORAGE Product should be stored in a cool, dry location in unopened containers at a temperature between c between 46℉ (8℃) to 82℉ (28℃) unless otherwise stated. To prevent contamination of unused product, do not return any material to its original container. DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliable at the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have no control. It is the responsibility of the customer to determine the products suitability for use. DEDT New materials Limited and its associated companies accept no liability arising out of the use of this information or the products described herein.

共 3 條記錄1

推薦產品

DEDT 8416瞬干膠
DEDT 835瞬干膠
DEDT 1770處理劑
DEDT AC9促進劑
DEDT 1050AB膠

狼人综合亚洲色图_亚洲第一页自拍1414_健身房媚药中文字幕_国产精品福利一区二区无码_最近2019免费手机_亚洲国产综合久久灌醉_欧美性爱网站成人_他含着她的乳奶揉搓揉视频捏_成年人免费看黄色毛片_日韩一二三区视频精品